1. 全國免費招商熱線: 400-800-4491
      產品諮詢訂購電話: 134-1834-4523
       當前位置:模具防鏽劑首頁 - 新聞動態 - 技術分享 - 模具維修

      塑料模具專業英語

      發佈時間:2016.09.24 新聞來源:脫模劑_防鏽劑_清洗劑_頂針油_深圳金利源精細科技有限公司

      模具述語

      一、入水:gate

      進入位: gate location

      水口形式:gate type

      大水口:edge gate

      細水口: pin-point gate

      水口大小:gate size

      轉水口: switching runner/gate

      唧嘴口徑: sprue diameter

      二、流道: runner

      熱流道: hot runner,hot manifold

      熱嘴冷流道: hot sprue/cold runner

      唧嘴直流: direct sprue gate

      圓形流道:round(full/half runner

      流道電腦分析:mold flow analysis

      流道平衡:runner balance

      熱嘴: hot sprue

      熱流道板:hot manifold

      發熱管:cartridge heater

      探針: thermocouples

      插頭: connector plug

      插座: connector socket

      密封/封料: seal

      三、運水:water line

      喉塞:line lpug

      喉管:tube

      塑膠管:plastic tube

      快速接頭:jiffy quick connector plug/socker

      四、模具零件: mold components

      三板模:3-plate mold

      二板模:2-plate mold

      邊釘/導邊:leader pin/guide pin

      邊司/導套:bushing/guide bushing

      中託司:shoulder guide bushing

      中託邊L:guide pin

      頂針板:ejector retainner plate

      託板: support plate

      螺絲: screw

      管釘:dowel pin

      開模槽:ply bar scot

      內模管位:core/cavity inter-lock

      頂針: ejector pin

      司筒:ejector sleeve

      司筒針:ejector pin

      推板:stripper plate

      縮呵:movable core,return core core puller

      扣機(尼龍拉勾):nylon latch lock

      斜頂:lifter

      模胚(架): mold base

      上內模:cavity insert

      下內模:core insert

      行位(滑塊): slide

      鑲件:insert

      壓座/斜雞:wedge

      耐磨板/油板:wedge wear plate

      壓條:plate

      撐頭: support pillar

      唧嘴: sprue bushing

      擋板:stop plate

      定位圈:locating ring

      鎖釦:latch

      扣雞:parting lock set

      推杆:push bar

      栓打螺絲:S.H.S.B

      頂板:eracuretun

      活動臂:lever arm

      分流錐:spure sperader

      水口司:bush

      垃圾釘:stop pin

      隔片:buffle

      彈弓柱:spring rod

      彈弓:die spring

      中託司:ejector guide bush

      中託邊:ejector guide pin

      鑲針:pin

      銷子:dowel pin

      波子彈弓:ball catch

      喉塞: pipe plug

      鎖模塊:lock plate

      斜頂:angle from pin

      斜頂杆:angle ejector rod

      尼龍拉勾:parting locks

      活動臂:lever arm

      復位鍵、提前回杆:early return bar

      氣閥:valves

      斜導邊:angle pin

      術語:terms

      承壓平面平衡:parting surface support balance

      模排氣:parting line venting

      回針碰料位:return pin and cavity interference

      模總高超出啤機規格:mold base shut hight

      頂針碰運水:water line interferes withejector pin

      料位出上/下模:part from cavith (core)side

      模胚原身出料位:cavity direct cut on A-plate,core direct cut on B-plate.

      不準用鑲件: Do not use (core/cavity) insert

      用鈹銅做鑲件: use beryllium copper insert

      初步(正式)模圖設計:preliinary (final) mold design

      反呵:reverse core

      彈弓壓縮量:spring compressed length

      穩定性好:good stability,stable

      強度不夠:insufficient rigidity

      均勻冷卻:even cooling

      扣模:sticking

      熱膨脹:thero expansion

      公差:tolorance

      銅公(電極):copper electrode



      Tags: 塑料 模具 英語 脫模劑